# What is qPCR?

> Written with AI · [Biotechnology: molecular diagnostics, reading DNA to answer questions](https://lessoons.com/en/molecular-diagnostics) · Grade 12 · 2026-11-13 · https://lessoons.com/en/molecular-diagnostics/what-is-qpcr

qPCR, quantitative or real-time PCR, is PCR that measures how much target DNA a sample held at the start. A fluorescent dye or probe glows more as copies build up, the machine reads it after every cycle, and the threshold cycle, Ct, where the glow crosses a set line, comes earlier the more target there was: about one cycle earlier for each doubling.

## The topic explained

### PCR that counts

Ordinary PCR answers yes or no: after 30 cycles a band on a gel shows whether the target was there. qPCR, quantitative PCR, also called real-time PCR, answers how much. The tube holds a fluorescent signal that grows with the product, and the machine reads it after every cycle, building an amplification curve. Higuchi and his colleagues introduced this real-time reading in the early 1990s. The machine reads through the closed tube, so the product never has to be opened on a bench, which lowers the risk of contaminating later tests.

There are two common signals. SYBR Green is a dye that glows when it binds any double-stranded DNA; it is cheap, but it also lights up a wrong product, so a melt curve at the end checks that only one product formed. A hydrolysis probe is a short strand that binds the target between the two primers and carries a reporter dye and a quencher that keeps it dark. As the polymerase extends the primer, it cuts the probe, the reporter is freed from the quencher and glows. Only the target sequence can bind the probe, so the signal is specific.

### The threshold cycle

Every amplification curve has three parts: a flat baseline while the product is too little to see, an exponential rise as it doubles each cycle, and a plateau when primers and nucleotides run low. A threshold line is set across the exponential part, and the cycle at which a curve crosses it is the threshold cycle, Ct. The more target at the start, the fewer cycles are needed, so a lower Ct means more target. The threshold is placed above the noise of the baseline, where every curve is still rising exponentially, so that all reactions are compared at the same point.

With perfect doubling, each cycle earlier means twice as much target. In the invented curves, sample A crosses at 21.9 and sample B at 24.9, three cycles apart, so A held 2³ = 8 times more target than B. Ten times more target is log₂ 10 ≈ 3.32 cycles earlier. The common misreading is that a high Ct means a lot of target; it is the reverse.

### From Ct to a number of copies

To turn Ct into copies, a standard curve is run on the same plate: dilutions with known numbers of copies, from 10² to 10⁶. Plotting Ct against the logarithm of the copies gives a straight line. In our example it is Ct = 38 - 3.32 log₁₀ N, so an unknown sample with Ct 26.38 has log₁₀ N = (38 - 26.38) ÷ 3.32 = 3.5, about 3,162 copies.

The slope also checks the reaction. The efficiency is E = 10^(-1/slope) - 1: a slope of −3.32 gives 1.00, perfect doubling, while −3.6 gives about 0.90, so only 90% of the molecules are copied each cycle. Laboratories usually accept efficiencies near 90 to 110%.

### What it measures, and its cautions

qPCR measures the amount of a virus in a sample, the share of GM material in a food, and, after reverse transcription, RT-qPCR, how strongly a gene is expressed compared with a reference gene in the same sample. The comparison is relative: if a gene's Ct falls by 2 after a treatment while the reference gene's Ct stays the same, the gene's RNA rose about 2² = 4 times. Every run needs a no-template control, which should stay flat. A Ct value depends on the sample, the kit and the machine, so it is compared only within one validated test, and a medical result is explained by a doctor.

## Practice: what qPCR is

For 12th grade biotechnology students. Use the graphs and numbers on the sheet, show every calculation, then check your answers.

1. **The marked points show where each curve crosses the threshold: sample A at cycle 21.9, sample B at 24.9. Which sample held more target, and why?** — Sample A, with Ct 21.9: it crossed the threshold earlier, so it needed fewer cycles and started with more target.
2. **How many times more target did sample A hold than sample B, assuming perfect doubling?** — They are 3 cycles apart, so 2³ = 8 times more target in sample A.
3. **Two samples have Ct 26 and Ct 30. How many times more target is in the first?** — 2^(30 - 26) = 2⁴ = 16 times more, assuming perfect doubling.
4. **Use the standard curve, Ct = 38 − 3.32 log N, to find the number of copies in the unknown at Ct 26.38.** — log₁₀ N = (38 - 26.38) ÷ 3.32 = 3.5, so N = 10^(3.5) ≈ 3162 copies.
5. **A standard curve has a slope of −3.6. Calculate the efficiency and say what it means.** — E = 10^(-1/(-3.6)) - 1 ≈ 0.90, so about 90%: in each cycle only about 90% of the molecules are copied, a little less than perfect doubling.
6. **Fill in step 3 and explain why a probe gives a more specific signal than SYBR Green.** — The polymerase cuts the probe as it extends the primer. The probe glows only after it has bound the target sequence and been cut, while SYBR Green lights up any double-stranded DNA, including a wrong product.
7. **The no-template control gives an amplification curve with Ct 33. What does this show, and what should be done?** — A contamination, or primers forming a product with each other. The results of the run cannot be trusted; the reagents are replaced and the run repeated.

## Common questions

### What is the difference between PCR and qPCR?

PCR copies a target and is usually checked at the end on a gel. qPCR measures fluorescence after every cycle, so it shows how much target the sample held at the start, without a gel.

### What does a Ct value mean?

The cycle at which the fluorescence crosses the threshold. A lower Ct means more starting target; each cycle earlier means about twice as much, with perfect doubling.

### What is the difference between RT-PCR and qPCR?

RT-PCR starts by copying RNA into DNA with reverse transcriptase. qPCR measures the product in real time. They are often combined as RT-qPCR, for example to measure an RNA virus or a gene's expression.

### Why is a standard curve needed?

Ct alone gives only relative amounts. Standards with known numbers of copies, run on the same plate, give the line that turns each Ct into a number of copies.

### What is a melt curve?

At the end of a SYBR Green run the product is slowly heated while fluorescence is read. A single sharp drop at one temperature shows one product; several drops show unwanted products.
